1.OBD Terminator introduction
The OBD terminator is a new diagnostic device developed by SHENZHEN STIC TECHNOLOGY Co., LTD, and it is very stronger powerful. Which can do immobilizer, Odometer correction, SI reset, Airbag reset, Synchronization and programming. And it includes the independent research and development OBD terminator program, and supports the J2534 diagnostic protocol compatible with Honda HDS, Toyota TIS, Jaguar, Land rover SDD2, Ford, Mazda IDS diagnostic software and compatible with IMMO VAG software, BMW software, Keys programmer software. The OBD terminator also supports the VAG 5 generation all key lost(it is the only support for Audi 5 generation. A4/A5/Q5/A6/A7/A8/VW Touareg)
2.OBD Terminator Hardware
The equipment part diagram is show below figure2-1.Description of parts:
①OBD Terminator Host
②OBD Communication Bus
④TAG Keys Read-Write Coil
⑤Blue Double-head cable
⑥HONDA 3-PIN Adapter
⑦KIA Communication Adapter
⑧Honda Communication Adapter
figure 2-1 OBD terminator device
3.1 OBD terminator quick loader
The OBD quick loader software is show as follow figure 3.1-1,the top left corner is the software name and the version number of the software, the bottom left corner is our company website, the center are software lists it include OBD terminator software list,J2534 software list,FVDI2 software list, Immo software list.
When you open the software that you want by quickloader, which maybe pop a prompt box it will say “remaining XXX days” or “Get the firmware information from the server” .Shows as follows figure3.1-2 and figure3.1-3.
Remaining time: OBD terminator device activate remaining time. The active days are 60 days and are automatically activated after each connected to the internet again. So, most functions of OBD can be operated without networking.
Get the firmware information from server: OBD terminator will get latest firmware from server when the network is connected. If there will latest firmware there is upgrade firmware.
Remark: OBD terminator all the software must be opened by quick loader software, otherwise, it will cannot be used normally.
figure 3.1-1 quickloader software
figure 3.1-2 activation time
figure 3.1-3 update firmware
3.2 OBD terminator
OBD terminator software interface shows as follow figure3.2-1,it is support English, Chinese, traditional Chinese. You can set the language that you want. Click the “Settings->update” you can see the information which is device id, firmware version, software version etc, Shows as figure3.2-2.OBD terminator tools menu, it include cipher calculator and Toyota smart card unlock function, Shows as figure 3.2-3.
PIN calculator: terminator customers can calculate free, enter the verification code directly into the software, calculator support Nissan, Ford, Jaguar land rover engineer code, Honda PIN. Shows as figure3.2-4 and figure3.2-5.
Toyota smart card unlocked: Support original Toyota smart card unlocked.
OBD terminator software can be used to immobilizer, Odometer correction, SI reset, Airbag reset, Synchronization and programming and so no. These functions are under development.
OBD terminator main support Audi 5 generations all key lost functions(support 2010-2013 years,A6/A7/A8/Touareg
figure3.2-1 OBD terminator software homepage
figure3.2-2 OBD terminator version information
figure3.2-3 tool menu
figure3.2-4 calculator login
figure3.2-5 Cipher calculator functions list
3.3 J2534 Compatible software
J2534 support diagnostic software which include HDS, TIS, Jaguar land rover SDD, Ford IDS, Mazda IDS, the following figure 3.3-1 shows.
Software installation tips: Ford, Mazda, jaguar land rover, Honda HDS, the three software can't be installed on the same computer. Toyota have no restrictions and don't clash with other software!
figure 3.3-1 J2534 software
3.4 Immo Software
Immo software support keys programmer software, VW/Audia software, BMW software. Show as follows figure 3.4-1.
The software must be used to connect the red dongle with blue double head cable, the USB cable of the red dongle must also be connected to the computer.
The OBD terminator is currently compatible with vvdi2-1.2.2.
figure 3.4-1 Immo software
3.4.1 keys programmer(TAG software)
TAG software includes transponder programming, special transponder, immobilizer data tool, prepare remote, copy remote, copy transponder, other key tool. remote frequency test functions. It also includes automatic transponder detection. As following figure 3.4-2 shows.
figure 3.4-2 TAG software
3.4.2 VW/Audi software
VW/Audi software includes diagnostic functions, key learning and special functions. as following figure 3.4-3.Special functions includes engine control unit,k-line instrument/immobox, change KM, component protection(A4/A5/A6/A8/Q5/Q7/Allroad). EEPROM dump tool,MED17/EDC17 dump tool,BCM2 dump tool, Gearbox.
figure 3.4-3 VM/Audi software
3.4.3 BMW software
The software support multiple language which include simple Chinese, English, Italian, Spanish,German, Hungarian, polish. There are Unit coding, Key learn, Special Function, Flash Programmer in the menu bar. There is CAS/EWS Information, Immobilizer Information, File Make Key, Unlock Key option in the key learn menu. There is File Change KM,CAS Repair option in the special function menu. The BMW software interface is showing below.
figure 3.4-4 BMW software
4.How to connect OBD terminator
Install the latest software before connecting the device, and then connect to your device as show below figure 4-1.
figure 4-1 Connected to OBD terminator
Read More Related Information